It's a can holder. Four ice shards grip the can and hook in over it, an arcade of pointed arches ties them together around the back like the windows of a frozen citadel, a runeblade rises behind it like Frostmourne, and it stares back at you with two dark eyes. A cup underneath catches the sweat. It looks like a piece of Icecrown that fell out of a raid boss's loot. Fits the tall 500 ml cans. Desk stand, wall bracket, or the three-can Frozen Throne. One colour or two.
The four tall shards bow out and then hook back over the can by about 3 mm. Bump the desk and the can rocks into the claw instead of out of it. They stop 1.5 mm short of the can, so nothing scratches the paint. The arches between them are 45° on the underside, so they print without a single support.
The front panel is a black plate set 2 mm into the body with a 65° bevel around it. The claw mark is a white inlay printed 0.4 mm below the surface. No sticker, no paint. You can't scratch it off because there's nothing on top to scratch.
A cold can drips for an hour. Inside the claw sits a separate cup with a raised grid floor and four drain holes, so the can never stands in its own puddle and your desk never gets that ring. Pull the cup out, rinse it, drop it back in.
iDEALVISAMCApple PayGoogle PayBancontact
Every picture on this page is rendered from the file the printer gets. No retouching. What you see is what comes off the print bed.
Every overhang stays under 45°: 45° roofs on the windows and eyes, 65° bevels, shards that lean in, arches with 45° undersides, chipped edges, all within the limit. No support scars to sand off, no weak spots.
The black tips, foot band, rim, panel and cup are separate bodies printed in the same job as the white body. The colour is the plastic itself, so it can't chip.
The cup is 68 mm inside for a 66 mm can and the shards stop 1.5 mm short of it. The can drops in and out without scraping, and it doesn't rattle.
2 mm walls, a raised grid floor, four 5 mm drain holes. Rinse it under the tap, drop it back in.
Two keyhole slots, 40 mm apart, for 4 or 5 mm screws with a head up to 9.5 mm. Hang it, drop the can in.
0.2 mm layers, three walls, finer layers on the bevels. Every holder gets looked at before it goes in the box.
| Option | Mount | Finish | Height | Price | Select |
|---|---|---|---|---|---|
 Desk · Monochrome | Desk stand | Black or white | 177 mm | €23.99 | |
 Desk · Two-tone | Desk stand | White + black accents | 177 mm | €27.99 | |
 Wall · Monochrome | Wall bracket | Black or white | 134 mm | €26.99 | |
 Wall · Two-tone | Wall bracket | White + black accents | 134 mm | €30.99 | |
 Throne · Monochrome | 3-can plinth | Black or white | 204 mm | €64.99 | |
 Throne · Two-tone | 3-can plinth | White + black accents | 204 mm | €74.99 |
Measured on the print file. Print tolerance about ±0.3 mm.
If it's the tall 500 ml can (66 mm across, 168 mm high), yes, that's what it's built around. Regular 330 ml cans are the same width and sit fine, just lower. Anything wider than 66 mm won't go in.
Dual-nozzle printer. The black parts (tips, foot band, rim, front panel, cup) are separate bodies in the same print job, so they fuse with the white body layer by layer. Nothing is painted or glued, so there's nothing to chip.
Yes. The wall version swaps the back blade for a plate with two keyhole slots, 40 mm apart, for 4 to 5 mm screws with a head up to 9.5 mm. Tick the wall kit and the screws, plugs and a paper drilling template come in the box.
No. PLA goes soft around 55 °C. Rinse the cup under the tap and wipe the holder with a damp cloth. Don't leave it on a car dashboard in July either.
We print it after you order, so 2 to 4 working days, then tracked shipping: 1 to 2 days in the Netherlands, 2 to 4 to Belgium and Germany, 4 to 8 to the rest of Europe, 6 to 12 to the US and Canada, 8 to 20 anywhere else. The tracking link comes by email.
Almost certainly. We post to 175 countries from the Netherlands, all tracked. Pick your country above the Checkout button and the exact shipping price appears before you pay: €4.95 in the Netherlands, €7.95 to Belgium and Germany, €11.95 to the rest of Europe, €19.95 to the US and Canada, €29.95 everywhere else. Customs duty outside the EU is on you.
Send it back within 30 days, unused and in its box, and you get the product price back. Return shipping is on you, unless it arrived broken, then we replace it and pay for everything.
These four are what we print on demand. Want something else? Email hello@clawholder.com. Small batches are usually doable.